1) Before you went out and buy Brother Toner cartridges, you must make sure you know what model printer you have to insure product compatibility. Note down the model no . so that you can reference it when you’re in the store or online shopping.

2) After you have the correct Brother Toner to your printer model, power your printer OFF and open the cartridge box.

3) Next, you need to open the top cover of the printer. You should do that carefully in order to avoid problems for the interior or outside of the printer.

4) If the printer top cover is taken away, you want to extract the empty Brother Toner cartridge from the printer by pulling upward and away from the machine. You are able to do that without a great amount of force.

5) After you’ve taken the Brother Toner cartridge on the printer, you would like to prepare the new cartridge for insertion. To do this, you need to remove it from your plastic bag it is contained in. Next, you might want to remove the rip strip from the cartridge. The rip strip is mounted on a plastic film strip. Removing the rip strip is important because if you don’t your printer will only produce blank sheets. Take care when ripping the strip off, because you can get Brother Toner on your own clothes that may stain. If you end up spilling toner on yourself you’ll be able to wash it off with cold water.

6) Next, you want to place the fresh new cartridge in the printer the same way the old Brother Toner cartridge arrived. There will most likely be arrows at the package to show you inside the placement that can assist you ensure that you’re putting it in correctly. Exactly like removing the used Brother Toner cartridges, it should slide in with minimal force. If isn’t going to slide in easily you must be sure the Brother Toner cartridge is the correct cartridge for your model printer and then be sure that it’s aligned correctly.

7) After you have the cartridge inside the printer properly, place the printer lid back on.

Now you are going to print several test pages to make certain that everything is working the way it should. When the print outs look nice: You are done. Package the existing toner cartridge in the box the new toner arrived and recycle it. If your print outs look bad: Sometimes cartridges could be defective. If there have been problems with your test pages, you may need to attempt the process again with another toner cartridge.

1. The printer points the full capacity of toner. It shows low toner; that means that few hundred of pages may be printed with no problem.

2. Repeated shortcomings of similar variety could be developed in pages.

3. Users can modify the toner in grayscale printer. But it is not easy to switch the color toner of the colored printer. You need to ring the helpdesk for any adjustments to color printer.

4. The appearance of the turning out of printer may be withered.

Type of printer

Generally two names are subscripted around the printer, the first is the printer’s name plus the other is its model name. What’s necessary to change a toner cartridge is a model name. Only with this particular information, store person can inform you in regards to the toner cartridge that need be applied. If you have any confusion about the exchange, what you have to do is to give your serial number to manufacturer to ensure to get appropriate toner cartridge.

There is a few Steps if you want to switch toner cartridge:

1. New cartridge is taken back to the printer and fresh toner cartridge is put aside from the package.

2. Turn off the printer.

3. Then you need to remove the tone cover from the printer.

4.  After that remove the older toner from the printer. It should show low tone to print with a modest level of a pressure.

5. Take out the brand new toner and remove the strip from the cartridge. Be careful that there’s a small tab certain to plastic strip assisting the cartridge. This strip can also be to be removed; else the printer prints only blank sheets. Be careful that this toner isn’t spilled over you. If it happened, then you need to wash it off with cold water.

6. Fix the brand new cartridge inside the printer in the similar manner while you removed an older one. There will be directions to help you to place it correctly.

7. After setting down the cartridge, place the toner cover over it.

8. Switch on the printer.

9.  Print few pages

if the print appears wonderful then you are successful with your work. Now you need to Pack the old cartridge in the pack like the new one and give it to some recycler. People might get the credit for their old cartridges.
Deducing the fault, if any

Sometime there can be some problem with the trial pages as the cartridge may be faulty or refurbished. If there is a change that was not with the previous toner, there will be some problem with the toner cartridge. Use another cartridge and see the change in printing. If there is again the same problem then there might be problem with the printer else with the toner cartridge.

1) Before you go out and purchase Brother Toner cartridges, you need to make sure you understand what model printer you’ve got to insure product compatibility. Write down the model number to help you reference it when you are in the store or online shopping.

2) Once you’ve the proper Brother Toner to your printer model, power your printer OFF and open the cartridge box.

3) Next, you have to open the top cover of the printer. You should do that carefully in order to avoid problems for the interior or outside of the printer.

4) When the printer top cover is removed, you would like to extract the empty Brother Toner cartridge on the printer by pulling upward and from the machine. You must be able to do this without a great amount of force.

5) Once you have taken the Brother Toner cartridge from your printer, you want to prepare the brand new cartridge for insertion. To achieve this, you must remove it from the plastic bag it is contained in. Next, you need to remove the rip strip on the cartridge. The rip strip is attached to a plastic film strip. Removing the rip strip is very important because if you do not your printer will simply produce blank sheets. Be aware when ripping the strip off, as you may get Brother Toner on your own clothes which can stain. If you end up spilling toner on yourself you can wash it off with cold water.

6) Next, you want to place the new cartridge in the printer exactly the same the old Brother Toner cartridge came out. There will likely be arrows in the package to show you within the placement that may help you make sure you’re putting it in correctly. Much like removing the used Brother Toner cartridge, it should slide along with minimal force. If it does not slide in easily you should make sure the Brother Toner cartridge is the correct cartridge for your model printer then guarantee that it is aligned correctly.

7) Once you have the cartridge inside printer properly, put the printer lid back on.

Now you may want to print a few test pages to make sure that things are working the way in which it should. If the print outs look nice: You’re done. Package that old toner cartridge in the box the new toner arrived and recycle it. In case the print outs look bad: Sometimes cartridges could be defective. If there were problems with your test pages, you may need to test the process again with another toner cartridge.
I hope this tips will help you on how to change brother toner cartridges correctly